ACCESSORIES
- 45 mil membrane – 5’ x 100’ Termination Bar 10’ – predrilled (requires 21 anchor pins)
- 45 mil membrane – 10’ x 100’ Anchor pins 7/8” – sold by the box – 100/box
- 60 mil membrane – 5’ x 100’ Anchor pins 1 ¼” – sold by the box – 100/box
- 60 mil membrane – 10’ x 100’ Anchor pins 1 ½” – sold by the box – 100/box
- Coverage 10’ x 100’ roll Anchor pins 2” – sold by the box – 100/box
- Fastened – 5” lap, 958 sq. ft. 2” Barbed Plates Galv. – 1000/box
- Adhered – 3” lap, 975 sq. ft. 3” Ribbed Plates Galv. – 1000/box
- Ballast – 3” lap, 975 sq. ft. 1 5/8” Screws – 1000/bucket
- 2 ¼” Screws – 1000/bucket
- 2 7/8” Screws – 1000/bucket
- Detailing membrane 24” x 50’ 3 ¼” Screws – 1000/bucket
- Cover Strip 6” x 100’ (used at perimeter to get a 15 yr. warranty) 4 ½” Screw – 1000/bucket
- Roof Transition Anchor Strip (RTA Strip) 6” x 100’ 6” Screws – 1000/bucket
- Universal Pre-Formed Corners 4” x 4” w/6” flange 8” Screws – 1000/bucket
- T-Joint Patches Hercules Retro 2” Drain W/Aluminum Body
- Pipe Boot pre-formed – 1” – 6” clamp ring included Hercules Retro 3” Drain W/Aluminum Body
- Cleaner 1 gal. – 5,000 l.ft./gal. Scupper Retro 2” Drain W/Aluminum Body
INSULATION BOARDS – recovery boards
- Bonding Adhesive (solvent base) 1 gal. – 50-60 sq. ft./gal 2 surface ½” High Density Wood Fiber 4’ x 8’
- Bonding Adhesive (solvent base) 5 gal. 250-300 sq. ft./pail 2 surface 1” Polyisocyanurate 4’ x 8’
- Everguard Caulk 10.3 oz – 15 l. ft. coverage 3/8” bead 1 ½” Polyisocyanurate 4’ x 8’ (use at upper lip of termination bar & around upper edge of penetration clamping rings) 2” Polyisocyanurate 4’ x 8’ (other thicknesses available)
- Everguard Block Mastic 10.3 oz. – 10 l. ft. 3/8” bead Dens-Deck® – thicknesses ¼”, ½” or 5/8” in 4’x4’ & 4’x8’ (use between flashing membrane & substrate surface, behind termination bars ¼” spans flutes with widths up to 2 5/8” and between roofing membrane and drain flanges) ½” spans flutes with widths up to 2 5/8”
- Everguard Cut Edge Sealant pint 5/8” spans flutes with widths up to 2 5/8” (use to seal the edge of a cut membrane to seal it from the elements) Pactiv Recovery Boards – for single ply membranes
- Coated Metal 4” x 10’ ( use at perimeter to get a 20 year warranty) PB6W – for mechanically attached systems
- Scuppers TPO Coated PB6FA – for fully adhered systems (compatible w/most adhesives) 4” x 6” x 12” or 8” x 10” x 12” Both are 3 lb. density extruded polystyrene for high compressive Drains with TPO membrane strength, 20 psi, 3 ply facers do not delaminate, does not absorb ½” to 6” in ½” increments water so it maintains its integrity, lightweight 10 lbs/100 sq. ft., Walkway Rolls 30” x 50’ gray only 4’x50’ fanfold bundle saves install time & money, UL & FM approved
- Pourable Sealer Pocket 17/32” 4’ x 8’ OSB
- Pourable Sealer A & B – does 2 pitch pans 6”x6”x4” high OMG SpotShot Adhesive – insulation
- Flexseal - can also be used w/fill as a pourable sealer OMG Dispensing Gun – for OMG SpotShot Tapered systems available for both ISO and EPS
