Royal Edge Non-Reinforced EPDM Membrane 3

Roofing Products International manufactures high performance single-ply roofing membrane systems and accessories for the industrial, commercial, and residential roofing markets. The same commitments to product quality and system performances, along with a dedicated sales and technical team, has made RPI into one of the most solid performers in the single-ply roofing industry. The incredible durability and performance characteristics of RPI Royal Edge TPO membrane and system components combined with ease of application and availability of wide sheets: translates into a lightweight installation, which provides excellent protection from constantly changing weather extremes.

APPLICATION INSTRUCTIONS:

1. All substrates must be dry, clean, and free of debris and loose foreign materials including oils, grease, and other contaminants.
2. All surfaces must be smooth and free of sharp and protruding edges.
3. All voids greater than ¼ inch should be filled with an acceptable material.
4. RPI Royal Edge EPDM must be installed according to RPI System Specifications.

PRECAUTION:

1. When moving/transporting, avoid dragging rolls. Do not allow membrane to come into contact with objects that can puncture, cut, or tear the membrane.
2. Prevent contact with products such as oils, animal fats, petroleum products, and grease.
3. Refer to Material Safety Data Sheets (MSDS) for safety information and disposal

RECOMMENDED STORAGE:

1. Protect membrane from puncture and other physical damage.
2. Before stocking/loading rooftop, check existing structure to ensure dead load limitations are not exceeded. Consultation with a structural engineer is recommended.
3. Do not store material near ignition or open flame sources. Material will burn when exposed to open flame.

Free 40 Year Membrane Only Warranty

(60 mil fully adhered to ISO for residential and commercial roofs)

Labor warranties available for a nominal fee for periods of 5, 10 & 15 years through the Registered Applicator Program.  Labor warranties are not available for residential installations.

EPDM – Black (private label firestone – low talc)

ACCESSORIES

• 6” x 50’ uncured flashing
• 6” x 100’ uncured flashing
• 12” x 50’ uncured flashing
• 12” x 100’ uncured flashing
• 6” x 25’ uncured flashing w/tape
• 6” x 50’ uncured flashing w/tape
• 6” x 100’ uncured flashing w/tape
• 5” x 100’ Cover tape
• 9” x 50’ Cover tape
• 6” x 100’ Reinforced perimeter strip (not required for warranty)
• Seam Tape – 3” x 50’ – must use primer/activator – (cleaner if needed)        
• Seam Tape – 3” x 100’– must use primer/activator – (cleaner if needed)      
• Seam Tape – 3” x 100’– must use primer/activator – (cleaner if needed)
• Bonding Adhesive (yellow) – 5 gallon (avg. 325 sq. ft./5 gal)
• Splice Adhesive (seam 6”) – 1 gallon (avg. coverage 100 sq. ft./gal) (Must use with rubber to rubber application.  Use cleaner and splice adhesive.)
• Primer/Activator – 1 gal. – use only with applications using seam tape                                                                                                                                                             (Rubber to rubber contact requires using Splice Adhesive & Cleaner. If using seam tape must use Primer/Activator – Cleaner if needed.)

WHITE EPDM & ACC.

• 60 mil membrane White 10’ x 50’              
• 60 mil membrane White 10’ x 100’                      
• Uncured Flashing W/Tape White 6” x 100’
• Uncured Flashing W/Tape White 12” x 50’    
• Cured Flashing W/Tape White 6” x 100’    
• Cured Flashing W/Tape White 12” x 50’  
• 3” x 100’ Seam Tape (clear)  
• Tape Primer gallon (clear)
• Lap Sealant (white) avg. coverage 25 l. ft.
• Pipe Boots W/Tape (white)

ACCESSORIES

• Lap Caulk (paste sealant) – (avg. coverage 25 l. ft.)
• Pipe Boots 1”-6”
• Pipe Boots 1’-6” w/tape
• Pitch Pocket
• Pourable Sealer
• Flexseal – can also be used w/fill as a pourable sealer
• Termination Bar 10’ – predrilled (requires 21 anchor pins)
• Anchor pins 7/8” – sold by the box – 100/box
• Anchor pins 1 ¼” – sold by the box – 100/box
• Anchor pins 1 ½” – sold by the box – 100/box
• Anchor pins 2” – sold by the box – 100/box
• 2” Barbed Plates Galv. – 1000/box
• 3” Ribbed Plates Galv. – 1000/box
• 1 5/8” Screws – 1000/bucket
• 2 ¼” Screws – 1000/bucket
• 2 7/8” Screws – 1000/bucket
• 3 ¼” Screws – 1000/bucket
• 3 ¾” Screws – 1000/bucket
• 4 ½” Screw – 1000/bucket
• 6” Screws – 1000/bucket
• 8” Screws – 1000/bucket
• Hercules Retro 2” Drain W/Aluminum Body
• Hercules Retro 3” Drain W/Aluminum Body
• Scupper Retro 2” Drain W/Aluminum Body

INSULATION BOARDS – recovery boards

• ½” High Density Wood Fiber 4’ x 8’
• 1” Polyisocyanurate 4’ x 8’
• 1 ½” Polyisocyanurate 4’ x 8’  
• 2” Polyisocyanurate 4’ x 8’ (other thicknesses available)
• Tapered systems available for both ISO and (Use with single-ply, BUR, modified bitumen and fluid applied.)

Pactiv Recovery Boards – for single ply membranes

• PB6W – for mechanically attached systems
• PB6FA – for fully adhered systems (compatible w/most adhesives)