EPDM – Black (private label firestone – low talc)
- 45 mil membrane – 10’ x 25’
- 45 mil membrane – 10’ x 50’
- 45 mil membrane – 10’ x 100’
- 45 mil membrane – 20’ x 25’
- 45 mil membrane – 20’ x 50’
- 60 mil membrane – 10’ x 25’
- 60 mil membrane – 10’ x 50’
- 60 mil membrane – 10’ x 100’
- 60 mil membrane – 20’ x 25’
- 60 mil membrane – 20’ x 50’
ACCESSORIES
- 6” x 50’ uncured flashing
- 6” x 100’ uncured flashing
- 12” x 50’ uncured flashing
- 12” x 100’ uncured flashing
- 6” x 25’ uncured flashing w/tape
- 6” x 50’ uncured flashing w/tape
- 6” x 100’ uncured flashing w/tape
- 5” x 100’ Cover tape
- 6” x 100’ Reinforced perimeter strip (not required for warranty)
- Seam Tape – 3” x 50’ – must use primer/activator & (cleaner if needed)
- Seam Tape – 3” x 100’– must use primer/activator & (cleaner if needed)
- Bonding Adhesive (yellow) – 1 gallon (avg. 65 sq. ft./gal)
- Bonding Adhesive (yellow) – 5 gallon (avg. 325 sq. ft./5 gal)
- Splice Adhesive (seam 6”) – 1 gallon (avg. coverage 100 sq. ft./gal) Use with rubber to rubber application. Use cleaner and splice adhesive.
- Primer/Activator – 1 gal. – use only with applications using seam tape
- Cleaner – 1 gallon
- Rubber to rubber contact requires using Splice Adhesive & Cleaner.
If using seam tape must use Primer/Activator & (Cleaner if needed
ACCESSORIES
- Lap Caulk (paste sealant) – (avg. coverage 25 l. ft.)
- Water Cut-Off mastic (termination caulk) – (avg. covera
- Pipe Boots 1”-6”
- Pipe Boots 1’-6” w/tape
- Pitch Pocket
- Pourable Sealer
- Flexseal – can also be used w/fill as a pourable sealer
- Termination Bar 10’ – predrilled (requires 21 anchor pins
- Anchor pins 7/8” – sold by the box – 100/box
- Anchor pins 1 ¼” – sold by the box – 100/box
- Anchor pins 1 ½” – sold by the box – 100/box
- Anchor pins 2” – sold by the box – 100/box
- 2” Barbed Plates Galv. – 1000/box
- 3” Ribbed Plates Galv. – 1000/box
- 1 5/8” Screws – 1000/bucket
- 2 ¼” Screws – 1000/bucket
- 2 7/8” Screws – 1000/bucket
- 3 ¼” Screws – 1000/bucket
- 4 ½” Screw – 1000/bucket
- 6” Screws – 1000/bucket
- 8” Screws – 1000/bucket
- Hercules Retro 2” Drain W/Aluminum Body
- Hercules Retro 3” Drain W/Aluminum Body
- Scupper Retro 2” Drain W/Aluminum Body
INSULATION BOARDS – recovery boards
- ½” High Density Wood Fiber 4’ x 8’
- 1” Polyisocyanurate 4’ x 8’ 1
- ½” Polyisocyanurate 4’ x 8’
- 2” Polyisocyanurate 4’ x 8’ (other thicknesses available)
Pactiv Recovery Boards – for single ply membranes
- PB6W – for mechanically attached systems
- PB6FA – for fully adhered systems (compatible w/most adhesives) Spli
Use with rubber to rubber application. Use cleaner and splice adhesive. Both are 3 lb. density extruded polystyrene for high compressive
strength, 20 psi, 3 ply facers do not delaminate, does not absorb
Primer/Activator – 1 gal. – use only with applications using seam tape water so it maintains its integrity, lightweight 10 lbs/100 sq. ft.,
4’x50’ fanfold bundle saves install time & money, UL & FM approved. - 17/32” 4’ x 8’ OSB
